Read also:
difference between nan comfort and nan pro gold kogan tv launcher has stopped caffitaly coffee machine review woolworths error 37 fisher and paykel washsmart ozito push lawn mower review bridgestone ecopia ep300 review australiaGeorge Foreman Mix & Go Questions & Answers
GFBL300, with Chill Sticks (GFBL3002CS), Fitness Friend (GFBLP1), etc...29 questions from our users
syed a.asked
How do i reset George Forman Mix & Go, as the LED light keeps blinking? in the instructions it says if it over heats wait for 20 mins. I however have wated for an hours and when i turn it back on the led lights still blinks.
No answers
ROZasked
GFBL300. Blade attachment is stuck in Base. Tried turning it tight then wiggle it as I turned the opposite way.
Worked first time but now it has happened again and refuses to budge. As well as that, liquid leaked into Base and now it is rotting and smelly. How on earth do I get it all apart and then clean inside the Base. There doesn't appear to be a way to pull it apart for cleaning.
1 answer
I used a tea towel to hold the blades as they are sharp and I unscrewed the gasket on other side...take the gasket and washers off and wash, let dry and put back together.
Levona H.asked
I have just bought a George Foreman mix & go how on earth do I remove the rubber gasket in the blade assembly for cleaning.
You really don't have any info on this in the instruction book.
Thank you
1 answer
I used a tea towel to hold the blades as they are sharp and I screwed the gasket on other side...take the gasket and washers off and wash, let dry and put back together.
Liaasked
I've only just brought the mix and go, and used it once. Second time I tried it, it smelt burnt and was feeling warm. And now it doesn't seem to work and ideas of what happened to it?
2 answers
I’m not sure but that doesn’t sound right... I would check in the rim of the blade lid as there is a rubber ring - if that has dislodged it may have made that burning smell?? And if dislodged it may not work properly... otherwise I would take it back where I got it and see if it could be replaced as it may be a defect in the product??
I don't think it is unusual for the blade rim to be warm especially after use but if it doesn't appear to be working as it did I would definitely take it back.
Brimasked
I used my mix and go to blend some tuna chunks and avocado. I started to really slow down then stopped. Could smell an electric smell. I have turned it off but am worried I have burnt out the motor. Is there an overload reset or something else I can do?
8 answers
There is not a reset as far as I know. I have had my machine get a bit hot and I have solved this by using it in short bursts. Also if you move the mixture around a bit it is better. Makes me wonder if tuna and avocado are not liquid enough for this type of blender!
Great - thanks, pretty sure its toast as it wont restart.
Did you really think it is going to mix tuna? Mix and go is to make drinks!!!!! I use it for fruit drinks only. I mix frozen fruit with a little juice or water. It only gets a bit warm if too much is loaded into the container. Apart from my dust buster...this is the best piece of machinery I own!!!!
Steve Whittleasked
My mix and go was quite warm last time I used it. It smelt a tad weird so I switched it off. It won't turn back on. Is there anything I can do?
Gailasked
Can I get replacement seals for my mix and go if so where?
1 answer
Sorry, I'm not sure. I would contact them directly and ask for parts: http://www.georgeforeman.com.au/contact.aspx
Claire Lockettasked
Do you sell just the containers separately?
3 answers
Ummm...I don't sell the product. I just buy it.
If you are wondering, when you buy it, it comes with two containers.
Yes Claire . It comes with two containers but you can buy extras separately
This is what it says on the box...
Additional 600ml bottles sold separately.
Available in 4 colours.
ginny shearerasked
The lid of my mix and go is stuck and will not come out of the stand, has anyone encountered this, or found a way to get it out?
3 answers
By lid do you mean the blade attachment?
If so, and its stuck to the base of the blender,
First unplug the blender.
Use your bottle (making sure it's completely dry), twist it back on the blade assembly tightly(clockwise). When you feel that it's tight enough, twist it anticlockwise. You should feel a little give and it should come out as usual.
Thank you
Did you find that this worked? Mines still stuck and I don't know how else to get it off
Sharonasked
I have used my mix and go pro about 3 times and now the bottle leaks. Anyone else have this problem?
3 answers
Hi Sharon, no I have not had this problem.
Make sure the rubber seal is still in the base and that it's clean and sitting flush.
Make sure that the seal is not twisted. Can easily happen when refitting if it comes out when washing.
Its probe leaking thought spindle shaft o ring on the blades and not the rubber seal on the glass jug. I've had 2 replaced now but being a plumber have worked out how to fix it. you undo to blade assembly it has a backwards thread so you will undo it opposite way to turning a tap on. then pull the shaft out and grease it up with some silicone grease on the o ring aswel then put it back together. Seems to work fine now
Gabrielle48asked
The mix & go stays on
We have to turn it in & off from the wall switch
Is there a way to fix it?
5 answers
When you twist the bottle and push it downwards this makes it go on, and then you can twist it the other way to stop it. There's an arrow on the motor part and on the blade part that have to line up to make it go (which I gather you've already discovered if yours goes) and you just un-align them to make it stop and you can then remove the blade and bottle. Hope that helps. Cheers.
This answer is insufficient
Suggest you contact the George Foreman website. I have the Mix and Go Pro which may be slightly different from your model as mine has 4 options and has the blender jug as well as the bottle.
Teesha12asked
My mix n go has broken used a few times warranty run out the rubbers have all cone out round blade can i purchase just the blade attachment from anywhere and what price?
2 answers
As I live in New Zealand I am unable to give you an answer. Suggest you go back to the shop you bought it from and they should be able to advise you on what best to do. Good luck.
In NZ needapart.co.nz have replacement bases listed at NZ$21.95
Rogue80asked
I have the mix & go pro, tried to do ice but it just does the bottom & I have to shake it up. How do you do ice without shaking it up please as the instructions aren't clear?!
1 answer
I used to do ice and also nuts in mine and found that both would not completely crush. What I would do was start and stop the unit at the wall switch a few times. I would run for about five seconds and then let it settle for a few seconds and then run it again. Then run it for about a minute before finishing. Found that the large majority of the nuts/ice would get chopped up. Hope this helps. Cheers.
Sarahasked
Recently purchased a mix and go blender. The individual bottles seem to work fine but tried several times to blend watermelon in the jug and it takes ages for anything remotely to happen. Think the blades are too weak, the motor runs and bubbles start forming after five or so attempts with about 1mm blended. Really annoyed does anyone know how their warranty works? I bought it from myer this Christmas.
3 answers
Hi, I haven't tried the jug yet perhaps I should. The original bottle works well but the additional bottle leaks. I got in touch with George Foreman and I believe a replacement is being sent to me.
Try to add a bit of water, juice or any liquid.
You are taking about the mix and go pro with the 800watt motor. If you are call the distributor their name is Spectrum Brands Australia 03 8551 5000, it should work better than that
Booksasked
I have this machine do not know if it a blender, or something else, my daughter gave it to me, she never used it, it was a wedding present that she did not use. but lost the instructions booklet, It a George Foreman. GF.850, do you think you can help me? thank you.
shirley.x.meiasked
It states in the instruction in the cleaning section remove the rubber gasket from the blade assembly . How do I do that ? Seems I can not seperate the assembly at all.
christine.harmes.5asked
So I brought the mix & go blender along with an extra drink bottle yesterday and it work great with the clear drink bottle supplie the blade lid leads when attached to the extra blue drink bottle and doesn't seem to fit well? Is it not suppose to be attached?
- ‹ Prev
- Next ›
ieatwords.com.au has affiliate partnerships. These do not influence our content moderation policies in any way, though ieatwords.com.au may earn commissions for products/services purchased via affiliate links.