??!

141 questions from our users

Ozcoach

Ozcoachasked

WSF6606X (Stainless Steel)

We have an Westinghouse Dishwasher WSF 6608x which is 21 months old. It is now showing and F9 fault. I have done some basic research on the drain outlet is clear. Please advise.



5 answers
paul miller
paul miller

That seems to be a flow control position error. You need to contact whoever you bought it from and INSIST on getting it fixed. If they refuse conract consumer affairs
Paul

Westinghouse
ELECTROLUX ..Westinghouse

Good morning,

Julie from Electrolux here.

If the issue you have raised is still not resolved at this time, can you please email me your contact details at [email protected] attention Julie Ticket Number 1196607
We would really like to assist you.
Thanks,



Julie

Tracy S.
Tracy S.

Hi Julie from Electrolux..we have the same F9 fault on our Westinghouse dishwasher also & require help please. Tracy.

June B.

June B.asked

WSF6606X (Stainless Steel)

My dishwasher is flashing an error code of H13. It won't start a wash.

2 answers
paul miller
paul miller

Delay has been selected. Cancel delay setting



June B.
June B.

Thanks very much. I sorted it out Paul. June

June B.

June B.asked

WSF6606X (Stainless Steel)

Error code of H13. What does that mean? It won't start the wash.

No answers
Richard B.

Richard B.asked

WSF6606X (Stainless Steel)

How do I change the default wash program?

1 answer
paul miller
paul miller

Do you have the manual? It is all in there

Samantha Jane

Samantha Janeasked

WSF6606X (Stainless Steel)

Are the dishes supposed to be dry at the end of the eco cycle? I installed mine today and the first wash on eco the dishes came out soaking wet. Whats the point of the dry cycle if they are wet?

2 answers
Mohammad
Mohammad

It dries the dishes slowly to save energy, I do my wash in the night and in the morning when I get them out its dry and very clean. happy with is product.

Samantha Jane
Samantha Jane

Hi. I think mine is faulty as the dishes are far too wet and aren't even dry in the morning

Melissa Hattingh

Melissa Hattinghasked

WSF6606X (Stainless Steel)

Hi our dishwasher takes awhile after pressing on to switch in and then display SP and run through till 9.5SP then gets stuck in eco. When we switch off and on again it does exuthe same. We use it around 1x a week and have had it now for 18 months. Help please

No answers
jayray

jayrayasked

WSF6606 Series

Can I fix an F5 error?

No answers
Nads

Nadsasked

WSF6606X (Stainless Steel)

Westinghouse Dishwasher SB926SL - stopped working and panel display is stuck to 90 and is not changing. We have tried turning on and off and ending cycle etc but it seems the program button isn't working....On turning off and ON from the power switch, it goes back to 90 minutes. Is it a good idea to call a technician or change the dishwasher?

No answers
Colleen S.

Colleen S.asked

WSF6606 Series

Showing an F9 error. All lights flicking

No answers
Colleen S.

Colleen S.asked

WSF6606 Series

My dishwasher is showing an F9 error and all the lights are flicking

3 answers
Anita E.
Anita E.

Did you get a answer to this for mine has just done this

Alto L.
Alto L.

Handy Husband fixed it, our error F9 fixed by, Googling (Google) - Westinghouse dishwasher model wsf6608x flow control valve, under images open the pic diagram 942001222 00 - Wholesale Appliance Supplies, spare part 123 cost $9.90 picked up part from Northside Appliance Spares & Repairs Pty Ltd, 189 Robinson Rd, East Geebung, QLD, [email protected]
(Facing the dishwasher take off the left side panel and replace 123 part)

Peter T
Peter T

fixed the same fault by following the above advice. It's a "non return valve " and the part is just a $10 washer..yes part 123 in the pic diagram 94200122200. It's a simple fix, turn dishwasher on it's side (after all the disconnecting of hoses and power) and remove a hose clamp, pulled off the hose and replaced a washer(one way valve). Repair took 10 mins tops. works fine now..no F9

Dean. R

Dean. Rasked

WSF6606X (Stainless Steel)

Have a new dishwasher which doesn't dry the dishes very well even on Eco setting as suggested in manual. Also problem with bottom drawer coming off runner all the time. Any answers would be appreciated

No answers
JJFG

JJFGasked

WSF6606X (Stainless Steel)

Hi I keep getting F5 error. Drain is clean... any ideas ?

No answers
RaeBeav

RaeBeavasked

WSF6606X (Stainless Steel)

I can’t change cycle on my dishwasher - but instead of running 2.02 eco cycle, it is going for 0.01!
Tried unplugging & it comes up SP, lights flash & then runs through 1.SP-9.SP (I’d say about 5-10 minutes).
I have have this machine for about 3 yrs & no problems (except for a fault when first installed)
Can anyone help me diagnose this please - nothing in the manual

1 answer
NZKiwi
NZKiwi

The Dishwasher powder / tablet compartment is open. Close it, select programme,.... Start.

Bruce and Sandra M.

Bruce and Sandra M.asked

WSF6606X (Stainless Steel)

What does H24 mean

No answers
Bruce and Sandra M.

Bruce and Sandra M.asked

WSF6606X (Stainless Steel)

whAT DOES h24 MEAN

1 answer
Shiva
Shiva

Hello Bruce and Sandra,
H01-H24 refers to time Delay. So H02 means you have selected two hours delay.
Cancel the delay setting if you don't need it.

Paula P.

Paula P.asked

WSF6606X (Stainless Steel)

Hi my dishwasher is coming up with H12 error

No answers
Tracey M.

Tracey M.asked

WSF6606X (Stainless Steel)

Im getting the f5 error how do i get to the pipe thats connected to the pump any help would be great

1 answer
lance b.
lance b.

I am Getting the f5 error too, seems to be when it goes to do a rinse after a heating wash cycle. as in on intense cycle at 1hr and 3 left it drained then flashes F5. tried it on rinse cycle straight away after 2min same deal .

Mike in Redcliffe

Mike in Redcliffeasked

WSF6606X (Stainless Steel)

My dishwasher powers off completely two minutes before the end of every wash cycle except for rinse. Have to open the door for a few mins and close and press the on button several times before it finishes the last two minutes of the wash cycle and drains, have noticed it is very hot and steamy. Thoughts? Before I call a service man or do I buy a new dishwasher it is four years old

No answers
Helena Sowden

Helena Sowdenasked

WSF6606X (Stainless Steel)

Power button stopped working 2 wks ago, now flashing HO1

No answers
Aaron

Aaronasked

WSF6606 Series

Hi, i have the f5 code come up often, the water pipe has been replaced but still has the code, a technician is suggesting to replace the diverter valve, is this correct? Cheers

No answers
Page 2 of 8

Get an answer from our members and Westinghouse representatives

ieatwords.com.au has affiliate partnerships. These do not influence our content moderation policies in any way, though ieatwords.com.au may earn commissions for products/services purchased via affiliate links.