Read also:
kmart 2200w bagless vacuum review move yourself trailer hire melbourne aldi air conditioner split system ing orange everyday account review hoover eco pets turbo bagless vacuum reviews breville bread maker bbm100 reviewVicta Corvette Questions & Answers
VGMS464 (300, 4 Stroke), GCS466 (200, 4 Stroke), VGMS486 (400, 4 Stroke), etc...34 questions from our users
Henry P.asked
I have a victa corvette 750 mulch when I change the blades do I turn it up or on its side to change blades
No answers
Theplugasked
I have looked at all these reviews and I'm in shock with most. Do you people have anything between your ears? Blots etc come lose its called pre check and mantiance of your gear. I'd hate to to see your other equipment.
No answers
Allan Dinnarasked
What fuel is used please?
Shane D.asked
What size mower blades are required please? The handles have broken off as well. Am I able to be a replacement handle?
Thank you.
2 answers
Sorry. I meant buy replacement handles.
lots of people sell Victa parts on ebay - that's probably your easiest and cheapest way to buy a new handle.
Mower repair stores also sell new handles.
Removing one of your old blades will make it easy for you to compare with the exact correct blade at Bunnings or Supercheap Auto
Richieasked
Wat is the most common fault for starting the mower have spark fresh gas n many pulls no go
Rayasked
Why is this mower hard to start at least 6 to 10 pulls but after it’s warmed up take about 2 pulls. How come?
1 answer
I don’t know if whether or not you find it’s unique to this mower but I find all my power equipment always takes a few pulls when cold.
Generally, it’s because the engine is cold (ie not running at operating temperature). When the engine is not at operating temperature it’s harder to ignite fuel, sump oil is thicker and air is thicker. So, it’s easier to start the mower when hot because the fuel is easier to burn.
Jennyasked
Is the Corvette 300 heavier than the Corvette 100?
Jennyasked
How much does the mower weigh in comparison to the Corvette 200 and 300?
1 answer
200 is apparently weighs the same. 300 is 5kg heavier at 31kg. Numbers from victa website.
Donasked
HOW TO REMOVE ENGINE COVER TO CLEAN PLUG
1 answer
Sorry Don,
I have simply dumped my 18 month old victa and all the associated paper work in the tip!!! I do not want to know about these victas as they are just rubbish/money pits.
I recently bought a new Rover which has been working perfectly.
Cheers, Barry
Warwickasked
What type of spark plug is fitted to the Victa Corvette 700 lawn mower?
No answers
Walasked
my frame is rusted where the handle meet. I need a new frame. everything else is perfect. can this frame be supplied supplied?
1 answer
This is common with the steel framed Victas. Most mower shops will supply and fit a new deck, but the steel quality is poor, and you'll find the same thing happening within 12 months. If you can, pick up a good, second hand alloy deck.
Paulasked
Hi
When I pull the mower it starts to go then runs out of puff oil coming out of front
Just wondering what I can do?
I've checked spark plug air filter oil etc but still no good?
2 answers
Sounds like a real problem,sorry I can't think what it might be, best you put it in for a good service,,,,Bob..
You may have over-filled the crankshaft. Empty in until the oil is in the correct margin on the dipstick. Clean the air filter and spark plug. It may need to run for 10 minutes to clear the old oil. If it still blows smoke get it serviced.
Carlos Tasked
I need the spark plug can you help me on the number of the spark plug? thank you
No answers
Mattasked
Can anyone tell me what spark plug I need for my corvette 500?
1 answer
I bought a replacement spark plug for my Victa Corvette 750 19" mower last week (Model No GMS 488)
The spark plug I bought was a Champion RC12YC. Not sure if this spark plug is the right one for your mower? Suggest that you find out the make and model of your mower and engine and ring up a mower place and they can tell you what it should be.
Brent Hasked
Just to add to the question put 29/1/2016 the retailer thought they would solve the problem by lifting the engine about 5mm and increasing the revs to 3200rpm from 2800rpm. This had minimal effect but obviously created a further problem as it pushes the chassis further down into the cut area when attempting to cut at the same level. I have to lift the mower up one notch which does not cut the grass low enough. I am no technical person but clearly the problem is with the base plate which does not clear the grass to the catcher but the front wheel. It needs additional guard around the front of the plate and right front wheel. If any one can assist with the name of a good repair centre in Newcastle that can identify this problem please advise. Otherwise it will be a new mower and a waste of some hundreds of dollars thanks to Victa.
1 answer
I don't own this particular model of Mower though I'd recommend putting it back the way it is . you also have the option of buying another mower altogether
T.O.F.asked
faymax45asked
how much oil capacity?
Jayasked
My victa corvette 500 will only start with petrol into spark plug hole, priming button seems like not squeezing correctly any ideas appreciated
1 answer
Have to determine why the primer is not working. Leak or damaged bulb ? Have to resolve this as primer is required. Having to remove spark plug every time would be a pain. Good luck with it
barryasked
when is fuel tap on.. is it horizontal or diagonal for on?
Cant you tell which is correct way as it does not want to start at all?
Barry
ieatwords.com.au has affiliate partnerships. These do not influence our content moderation policies in any way, though ieatwords.com.au may earn commissions for products/services purchased via affiliate links.