Read also:
aldi weight loss shakes ingredients talon cockroach killer gel coles yates weed and feed reviews gleamous hot water system reviews super sleeper pro pillow review miele 09983500 complete powerline family all-rounder vacuum cleaner bubs goat milk formula reviewFisher & Paykel QuickSmart MW513 (5.5kg) Questions & Answers
33 questions from our users
vaniajonathan626asked
where is the lint disposable waste in this machine?and if it is internal I will like to know how it works, because eventually could block the machine...I just bought this machine...I have always clean the waste in my other ones...
No answers
Mick Rasked
Looking for the lint filter on mw513 machine serial number mrg497517
No answers
Jellyasked
How do you replace the drain hose on a MW513 washer ? Help appreciated.
No answers
Hanim H.asked
My F&P starts to fill with water after spin cycle is completed . Reasons/solutions ?
No answers
john chanasked
please tell me what is the product code number for Fisher & Paykel washing machine MW513 for registration purpose.
My email address : [email removed]
thanks
john
No answers
ccppwwasked
Hi I have a quicksmart MW513 and lint is left on my black clothes. Is there a lint filter I can clean? If so how do I do this. Thanks :)
1 answer
There is no lint filter available to you. It is internal to the machine and suppose to automatically empty. In your case it appears to clogged. I suggest that you run a high-water-level hot wash and see if that will clean it. I run one of these at least once a month. Otherwise put a microfibre cloth in with the load to pick up all the lint.
John M.asked
I have just moved house. I tried to wash today using my very reliable F&P MW513. It washed and rinsed but cut out completely when it reached ‘spin’ and about 1min 30 it tries again but then stops. It just keeps going in this loop. Doesn’t seem to be able to spin. Any thoughts?
No answers
PARasked
Washer stopped midcycle, no lights, beeps, completely dead. Power point OK. Is there a fuse or reset?
No answers
bryan h.asked
how do i change the waste pipe /outlet pipe on a mw513 washer the pipe has been cut and now it is to short to meet the drain it enters the machine 3/4 of the way up the back but the rear does not come off
No answers
Narelleasked
I set the water level and temp (cold as usual), pressed start and the 3rd and 4th lights (between long and short wash) and the spin light are on and it just beeps constantly. What is wrong? Thank you
No answers
Leka Bonoroasked
My mw513 stops after wash and do not pump out water to rinse and struggles, for 1 to 3 hrs and I had to switch it off and on again. How do I reset the operation?
2 answers
never had this problem
Usually it means that your pump has overheated and cut out. Buy a new pump from ebay. They are very simple to fit. To confirm the problem simply lift the lid just after it cuts out and sniff. If you smell a nasty electrical smell then it's definitely the pump. Another way is to plug the machine into a cheap $20 eBay power meter. When it switches on, the pump should be drawing about 80 watts. If you see it drawing hundreds of watts then all that power is going into cooking the pump. The pump cuts out automatically when it gets too hot and won't operate again until it cools down. It's a safety feature to prevent a red hot pump setting your machine on fire.
Sentuasked
My Top Loader MW513 no power at this moment. What is problem, anyone can help me please?
3 answers
not sure long as you have it turned on it should be right
No power, no any lights, not even any beep sound when power switch on in wall socket.
if turn power switch on wall on and no sound/ lights from machine - power board faulty.
RozzA McGeeasked
About 5-10 seconds into the spin cycle (before and after rinse) machine shuts down & lights blank out. About 30 sec later it comes back on with 2 sets of 2 quick beeps: low-high low-high, waits a little bit then tries the cycle again. If I do nothing, this repeats indefinitely (have left it going for 1hr+) and there are no fault codes showing in service mode. Disabling 'auto restart' does nothing, presumably because no actual fault code is throwing.. last fault was recorded hundreds of washes ago.
The ONLY error code I can find in diagnostics is for the user & it is OOB & this is not the issue.
It is taking between 1m15s and 1m30s to complete one of these reboot cycles & it's been running for over 1.5hrs so it's definitely gone past the 32 retry limit for self fault fix. What the actual heck is wrong with this thing? Going down the other questions about this model i can see a few people with approximately my issue & NO answers whatsoever.
I read somewhere it could be a faulty RPS sensor - ideas on how to test that?
Djlllasked
Does the new?mw513 have any lint filter?
2 answers
Really good question, I was confused by this myself. It does not have a lint filter like the previous washing machine I owned, it does manage to collect and extract the lint though, and does so better than my previous machine did. From the manual:
"Your washer has a self-cleaning lint system. The machine automatically separates the lint from the wash water, traps the lint between the inner and outer bowls and flushes it out at the end of the wash."
Djill
Thank you for answering this in full . It’s a great lityle machine
John L.asked
My MW513 splashes water during the wash cycle. The water is running down the inside of the cabinet and evaporating leaving soap powder around the inner channel at the bottom and also presenting on the pedestal (feet) at the floor. Any ideas what causes this ?
jordsneedshelpasked
Hi, I was selecting the wash cycle (like I normally would) and the machine made a click sound and then it lost all power. I have tried turning it off and on again and checked the outlet (which is still working with other appliances), but to no avail. Where do I start?
No answers
kenasked
our 315 washing machine has started 'clanking' while on wash mode? any suggestions ?
No answers
D and Pasked
Hi, Our washing machine is emptying very slowly and smells musty - any ideas?
Daniel Day-Lutzasked
Hi, the machine drains and fills water on same time. I turned the machine several times off and on. There’s no change. Please help! Thanks.
No answers
Cohen Wasked
Machine not spinning but will go throw cycles and drain what is the problem?
No answers
ieatwords.com.au has affiliate partnerships. These do not influence our content moderation policies in any way, though ieatwords.com.au may earn commissions for products/services purchased via affiliate links.