Read also:
pine discount quality furniture kenwick kenwick wa best steam irons 2017 australia polocool 6.0kw portable air conditioner microwave oven reviews 2015 australia how to reset euromaid washing machine ozito blower vac replacement bag electrolux ultraflex animal allergy pro vacuum cleaner review512 questions from our users
hendoasked
brake warning light on dash on start up, checked lights all ok, tailights are led with voltage load resistors,any ideas. no codes in system
No answers
flynn m.asked
Do these have traction control? If so how do I take it out/turn it off
No answers
Anthony S.asked
Is there a fuse for main headlights on a 2015 Holden Colorado
No answers
Rogeasked
I have a late 2014 RG Colorado.
Today I fitted new front brake rotors and pads. Vehicle went into limp mode. To get out of limp mode I found that if I switched the ESP off (held button for over 7 seconds) then the problem was removed. However when I stopped and switched the ESP back on went back into limp mode. What have I done wrong - what haven't I reset?
No answers
Ehd P.asked
Where is the location of Solenoid
No answers
Cath Dasked
6 speed manual 2014 LX colorado - Had no issues with gearbox and out of nowhere, I couldn't find 5th, so went back to 4th. Found 5th again further down the road and all seemed fine. Later that day, driving to shops, changed from 4th to 3rd, then couldn't find 4th again, locked me out of every gear while I was trying to find another gear. Can't select any gear with car stationary, both with engine on and off. When let foot off clutch it has a slight grinding noise - Could anyone tell me if this sounds like a selector issue or a seized gearbox. Cheers
No answers
Linda Gasked
Has anyone just had there steering go heavy and engine cut out on 2103 LTZ Colorado just over 130000 on the clock. Always been serviced.
No answers
vaughnasked
HI I have a friend who has no computer, he has a 2012 Colardo . The engine stopped as though it had run out of fuel this has happened twice in 3 weeks.
He replaced the filters during a service. after repriming the engine will start and run fine but with the engine warning light on whats going on with this vehicle
Thank You Vaughn G
No answers
Graham b.asked
How do you remove and replace the starter motor on a 2008 Colorado 4x4 with the v6 motor. Thanks
No answers
Kirsty D.asked
What rpm does everyone change gears in their manuals? Just brought my first diesel manual 2011 Colorado and trying to work out what works best for fuel efficiency.
Mark A.asked
how do I get my park light globe out of my 2011 rc holden Colorado
No answers
rayasked
what is a stabili control service
No answers
Ross C.asked
firstly I am assuming that the Colorado motor is at its "roughest" between 2 and 3000 revs because in this rev range it causes a vibration in predominately the left front side of the car . Has been doing this for about 80,000k now and its naturally getting worse. I guess most of you have had a problem and taken it to a mechanic and the bloody thing wont give the symptom at all or only slightly, this is what happened on the several occasions I have taken it to the dealer.The tone of the vibration/growl/noise or whatever you want to call it changes if the road has gentle undulations. I cant do too much investigation myself due to my arthritis but what I have found is in my opinion too much play where the inner front CV joints go into the gearbox ( I dont mean the joint itself but the actual outer body) this I feel would explain the change in tone going over undulations Any one else had this problem ?
No answers
Nash R.asked
I have bluetooth in my 2013 Holden Colorado RG LX and it will connect to calls but it wont connect to music coming from my phone. If anyone can help please text me [details removed]
No answers
Ben B.asked
Wanted to replace my 2012 Rg Colorado cabin filter but it doesnt allow access to the filter compartment. Any ideas how to get at the filter without major surgery?
2 answers
It may not have a cabin filter in it, you have to take the inner glovebox compartment out, think there’s a few 7mm bolts, but when you get to it you may find that where the opening usually is to change them, is actually sealed
I've resolved. It has to be cut out and a clip on cover bought from the manufacturer. The filter cartridge is inserted then the cover clipped on.
ieatwords.com.au has affiliate partnerships. These do not influence our content moderation policies in any way, though ieatwords.com.au may earn commissions for products/services purchased via affiliate links.