Westinghouse WSF6606 Series Questions & Answers (page 5 of 8)

Handy Husband fixed it, our error F9 fixed by, Googling (Google) - Westinghouse dishwasher model wsf6608x flow control valve, under images open the pic diagram 942001222 00 - Wholesale Appliance Supplies, spare part 123 cost $9.90 picked up part from Northside Appliance Spares & Repairs Pty Ltd, 189 Robinson Rd, East Geebung, QLD, [email protected]
(Facing the dishwasher take off the left side panel and replace 123 part)

Have you tried unplugging it at the wall leajingvit our for a minute and turning on again? I’d call where you purchased it from if it’s under warranty

Yes, tried unplug and plug back in & still not working

We have the same error at the moment, did you get an answer for your question. Any suggestions on how to fix it please

Contacted customer care? Very helpful they should be able to assist

Is your outlet hose blocked? The hose attachment on a pvc S-bend may need to be drilled open.

Just guessing but are your drains blocked do dishwasher not draining properly

Hi Sherree,
Not sure what this error is as I haven’t had any problems with mine.
I’d would search the trusty Google for answers & if nothing helps on there then I would contact Westinghouse.
Sorry I couldn’t help

Handy Husband fixed it, our error F9 fixed by, Googling (Google) - Westinghouse dishwasher model wsf6608x flow control valve, under images open the pic diagram 942001222 00 - Wholesale Appliance Supplies, spare part 123 cost $9.90 picked up part from Northside Appliance Spares & Repairs Pty Ltd, 189 Robinson Rd, East Geebung, QLD, [email protected]
(Facing the dishwasher take off the left side panel and replace 123 part)

Hi Dee which cycle are you using? some of the short/fast cycles don't run the drying heater, the manual shows which ones.

Yes keep switching btwn the 2 that dry...tried increasing rinse aid, everything the manual suggests. Have someone coming to check it out next week. Thank you for your reply.

Hello my dishwasher is showing error F9 too. I was wondering if you found out why and how to fixes the problem

It’s the drain hose filter. A new drain hose for approximately $30 and all fixed.

Handy Husband fixed it, our error F9 fixed by, Googling (Google) - Westinghouse dishwasher model wsf6608x flow control valve, under images open the pic diagram 942001222 00 - Wholesale Appliance Supplies, spare part 123 cost $9.90 picked up part from Northside Appliance Spares & Repairs Pty Ltd, 189 Robinson Rd, East Geebung, QLD, [email protected]
(Facing the dishwasher take off the left side panel and replace 123 part)

Try hold down the start/pause button for 3 seconds to cancel the load then restart it. I think that’s what I did last time. Maybe check the manual if that doesn’t work I remember just button mashing till it turned off or start a weird shorter load

Hi Mini you are right on the ticket. The H01 displays when you opt for time delay. You reset it by START/PAUSE
and use either the+ or - sign to select a new delay time. Naturally you have to press the start/pause to activate your choice. I hope this answers your question.
Kaz x

Hiya, yes that's right. I find this function particularly useful over night. So I program the machine to start a couple of hours before I get up in the morning so that it's just finished and I can open it and let the steam out, rather than it staying in all night

Thanks for the replies. Great help

Hi. I just had the same problem. It initially showed F5 then that sequence 1.5P-9.5P. I cleaned the inlet water filter then let the dishwasher go through the same sequence. It then went back to normal. The P sequence must be a diagnostic reset perhaps? Good luck I hope you’re back on track. I bought an extended warranty, still got 4 years to go.

Hi there, it seems like this error code is quite common, looking at other Westinghouse threads. I think you should contact Westinghouse on [email protected]
Good luck!