- Sign in
- Write a review
4WD Supacentre Questions & Answers (page 2 of 17)
Online store, Physical store (See All)339 questions from our users
Hi guys, can you fit your 9 inch spotlights to a 2022 hilux with an ARB bull bar without any radar cruise sensor issues
Hi Matthew,
I have seen customers do this and not have an issue, but my recommendation would be to speak to your dealership or insurance company to make sure before installation.
Regards, Mia
can the 6switch pad panel be connected to spotlights
Hi Troy,
No, it cannot as by law the spotlights can only be operated on a separate switch.
Cheers, Mia
Hi I have brought a plug and play wiring harms I’m just making sure I can run it in a Nissan navara NP300 with high beem ??
They run off a negative.
Hi there, the brand/model of the car usually doesn't effect the compatibility with this product as it is designed to be installed into any vehicle with aftermarket driving lights. However as advertise...
Read mored on our websites and listings this wiring kit will not work with vehicles installed with smart alternators. In regards to negative or positively run our manual is equipped with installation processes for both. Hope this helps, kind regards Jayde.Where is the serial or batch number located on
Kings 7” Domin8r Xtreme Driving Lights Fitted with OSRAM LEDs (Pair)
Hi Bec,
The product has no serial number. The batch number is usually printed on the plugs.
Regards, Mia
Hi i purchased a plug and play wiring harness kit as well as 7” inch spottier, i am currently installing them however the piggyback connector does not fit my headlight, are these plug n play kits suitable for a D22 Nissan navara 2014 ? thanks
Hi there,
Based on Google it says you should have a H4 which is one of the adaptors we sell.
Best to perhaps check your cars user manual if it's not a H4 or contact the dealer.
Regards, Mia
Hi i got 2 sets of 7inch spots 2 years ago gave one to son he put on his 2012 d max worked ok to day i put the other set on step daughters 1998 prado wired as instruction's but don't work low or high beam the red light on switch does not light up is there a need to revers the polarity or something thank Tom
Hi Tom,
Did you use the plug n play wiring kit or the spotlight wiring kit?
Regards, Mia
i used the one that came with the spoties and it also doesn't have the right plugs to click into the spot lights
i have 13volts at the switch 13 volts at head lights but no voltage from the small whi...
Hi Tom,
Can you please contact us here with evidence of the issue to assist further -https://service.4wdsupacentre.com.au/returns
Regards, Mia
Where do you find the serial/batch number on a Adventure Kinds standup paddleboard?
Hi Gary,
It will be on a white tag on the board, or it will be on the original packaging as the BN number
Cheers,Mia
Where is the batch/ serial number located on a Kings Dominator winch?
Hi there,
It is located on the end of the rope, printed usually in yellow.
Regards, Mia
I bought a light bar and some work lights as well as the appropriate plug n play harness, however the harness isn’t long enough to reach where I want to install my lights. How can I extent the harness?
Hi Willis,
We do not sell an extension kit, but they can be purchased at most auto parts stores.
Regards, Mia
Do you have a wiring harness for Mazda cx5
Hi Bob,
Our wiring harnesses come with H4 & HB3 headlight adapters which are the most universal fit for most vehicles. You may need to check your vehicles user manual if you require different adaptors to wire the lights.
Cheers, Mia
Am I able to run 4 9inch dominater spottieghs off the one wiring harness
Hi Caleb,
We'd only recommend either run the complete 2nd wiring harness from the other headlight (keeps the 2 harness electrical apart) or extend / modify the 1st harness from the relay to the light...
Hi I have installed a plug and play harness to my led light bar. It works but if I switch the light bar off by way of the toggle switch my left high beam fuse blows. What have I. done wrong. I rewired the toggle switch as it was but I can't figure out what is wrong.
Hi Davo,
Could you send us a video of this? Have you wired the product as per our instructions? Please email us at [email protected].
Talia
Thanks for your response but have fixed the problem the toggle switch was wired incorrectly from the box so when I replaced the wires after pulling the cable through the firewall they caused the short...
Read more after a lot of trial and error I found the correct sequence. Cheers thanks againI’ve bought a light at and plug n play spotlight kit for my boat so I don’t have headlights to run the harness into? How do I get the system to work?
Hi Neil, not sure how I can help mate, I’m just lucky to have good mates who are mechanics without them I’d be a fish out of water. I can asked them to for some help tomorrow at work if you need it?.
Regards
Mark W
It’s frustrating because I know the answer will be so simple…. Do I even need the harness…? Just wire it straight off a switch?
Hi mate the only way l have done it is to run the red headlight wire back to the battery this gives you power to the switch but not a auto electrician so don’t know if it’s a good idea or not
Hi, I have a light bar and a set of 7” spots on my BT50. Noticed last week there is a 1 second delay for light bar and 2 second delay for spots to go off when I dim lights. Have been working fine for the last 2 years.
Hi Egbert,
I apologise for the slight error, this may be a wiring issue. Please confirm your product has been wired as per our guidelines. Unfortunately as the item is out of warranty, any return fees are not covered.
Talia
Not seeking refund. Just want to figure out what is causing this delay. As I said, it did not happen before last week. Checked all connections and relays.
Hi Egbert,
To diagnose the issue we are going to need further information, please email us at [email protected] with your order number and a description of the issue if you would like to proceed.
Talia
hi, how do I connect the new 6 switch touch pad to my existing Kings wiring loom with my spot lights? ie when the touch pad switch in on the spot lights can only be activated by the high beam switch.
Hi Anthony,
Please see the link attached below for the instructions on how to have this installed.
https://indd.adobe.com/view/bc21c065-b991-494c-bbff-a5368f48ea85
Talia
thank, but how do you connect this to the cars high beam circuit? from what I understand by law you cannot run front spot lights on their own - they need to be controlled by the high beam switch. Th...
Read moreese instructions do not show how this done with this unit.Hi Anthony,
I have forwarded your question to our product development team to get you the clearest answer. Once they have responded, I will forward this to you.
Talia
Hi there. I’ve just hooked up my two nine inch lights and light bar combo exactly like the video said to. Problem is, the lights work on low beam but not on high beam. It’s probably just one wire needing to be swapped. Any help which wire to swap would be much appreciated. When the lights are on they are fantastic. On a side note, I paid exactly the same amount for the combo as I paid for a set of Narva 100 watt lights in 1989. Good value.
I've no idea why I am asked to answer any Q's given I've just had a most unsatisfactory experience with my purchases. After 3 faulty gazebos I've given up on their products.
Ok
Hi Harry,
Thankyou for reaching out!
In order to review the issue occurring we will need some further information....
I ordered and paid for an inverter instore on 9th August, they didn't have one and I was told that it would be at the store by mid September. On 24th September I called and was told a shipment had arrived that day and I should expect a call during the week to pick it up. A week later there was no call so I called again to inquired where my inverter is, only to be told that it wouldn't be delivered until the end of October. In the meantime they are still advertising this for sale on their website. How can you offer a product you don't have.
Hi Peter,
Unfortunately a number of our stock shipments have been delayed throughout the year as a result of the pandemic. Your original order is likely to have been a pre-sale, this would have been a...
Hi can you tell me what each wire color is for spotlight switch of kings wiring harness theres blue,white and black cant use original one supplied its to small to fit in original ranger blanks so I'm using a Narva switch but not sure which wires are power, accessories etc
Hi Dave,
White wire - Positive
Black wire - Negative (earth)...
which are the best performing Kings spotlights? Is it down to price or are there other factors to choose from, e.g. are they all pencil, all spread or a combination of both. I would like some technical advice. Are the 7" more robust than the 9" Thanks, Paul 0408 325 856
Hi Paul,
All spotlights are made to the same quality standard, to pick the best light for your vehicle depends on usage intent. Are you a frequent camper? What type of car do you drive? Please call us...
currently am running Kings 9” Spotties and want to add a light bar to my roof, assuming i wire it up using another smart harness at i able to plug one into the other and run it off the one headlight? cheers
Hi Anton,
The light bar will need to run off a separate harness. For details on whether this setup can run off the one headlight, please give us a call on 1800 88 39 64.
Regards, Talia
Get an answer from our members and 4WD Supacentre representatives
Other Camping Shops
ieatwords.com.au has affiliate partnerships. These do not influence our content moderation policies in any way, though ieatwords.com.au may earn commissions for products/services purchased via affiliate links.